6P_FTDL_13 – FTecu FlashTune kit for Kawasaki ZX6R ZX636 2019 2020

Description Your Kawasaki ZX6R / ZX636 already has a standalone ECU and now you can get a cable and software to re-program it! There is no longer any need to send us your ECU to remap, you can buy our DIY kit to fit to your own bike and remap and modify your own ECU! You can also directly import Power Commander III .djm or Power Commander V 5 .pvm fuel maps! You can de-restrict and Unleash Your bike’s ECU in 7 Easy Steps!   Select your base map (3 base maps are currently included)   Select your Ycc-T throttle map settings   Select your desired fuel map bias   Select your desired Engine Braking   Import a fuel map file   Choose your options (bypass EURO immobilizer, lower fan temps, speedohealer, rev limiter)   Flash the ECU! This Interface will remap & flash any ECU from the following bike models! ZX636 2019 2020 ZX6R 2019 2020 Example settings  2019 ZX636 – 21175-1387(US-ABS) StockECU  2019 ZX636 – 21175-1395(US) StockECU  ECU Mapping  Fuel  Ignition  STP Throttle  Traction Control  ECU Settings  Fan Temps  Decel Fuel Cut  Warmup Fast-Idle  Force QSS on  Exhaust Valve  ECT / USB Error  Stock O2  Evap Purge Valve  Air Switching Valve  ECU Modules  PC Fuel Import  2019 ZX636 – 21175-1386(US) StockECU  2019 ZX636 – 21175-1396(US) StockECU   The Flash-Tune Remap Interface allows you to easily adjust the following!   Enable Quickshifter   Enable Launch Control   Enable Pit Lane Limiter   Reduce Engine Braking   Remove Ycc-t Throttle Restrictions   Adjust Fuel Map Bias   Set High Load Fuel Maps (with PC3 and PC5 / PCV map importing)   Set Low Load (cruising) Fuel Maps for economy and Smoothness   Set Closed loop on O2 sensor (for more accurate tuning on a dyno)   Fuel Injector Proportioning   Modify Ignition Timing   Remove Immobilizer Function (mandatory on EU models)   Adjust Cooling Fan Temps   Adjust Rev-Limiter   Remove Top Speed Limiter   YCC-I RPM Control   Adjust Idle Speed Adjustment   ECU Based Quick-shifting (requires a Quickshifter kit)   Turn off AIS Pump   SpeedoHealer features – adjust the speedo to suit your fitted font and rear sprockets   Change Speedo into Gear indicator (10=1st, 20=2nd etc)   Permanently Remove ECU error codes   plus new features added with regular updates. This Data-Link ECU Flashing Kit Includes: FTdataLink ECU Interface USB Cable Bike-side programming harness to permanently install on your bike FT ECU License to allow unlimited flashes for a single ecu Flash-Tune FTdataLink ECU Remap & flashing interface cables eliminate the need for the following plug in devices and gives you YEC race kit like performance and features. – Power Commander or other piggy back fuel controllers – Power Commander Secondary Fuel Module – Power Commander Ignition Module – Bazzaz ZFTi – Two Brothers JuiceBox – Leo Vince Fast II fuel and ignition box ECU flashing is not only more cost effective than its alternatives but it is superior because but it also allows for more precise tuning fuel maps which automatically compensate for changing atmospheric conditions it allows for modification of parameters that are not otherwise tunable such a throttle valve actuation and engine brakingEveryone deserves the same tuning technology that until now was reserved for factory teams and riders with their YEC race kits. With Flash-Tune you can remove the restrictions that the factory must put in place to meet strict street vehicle emissions regulations for homologation, without the need for the factory race loom and factory YEC ECU. By using Flash-Tune to remap your ECU you are able to remap and tune your bike without interfering with critical correction factors resulting in smoother power gains than ever before possible. Flash-Tune Remap Products are under constant development. This product is for RACE USE ONLY and may invalidate your warranty. The included software will automatically update when connected to the internet as new features are added!